1) Show me/explain how you would check that the power steering is working before starting a journey.
CLICK FOR ANSWER
Gentle pressure on the wheel, maintained while the engine is started, should result in a slight, but noticeable movement as the system begins operating. Alternatively, turn the steering just after moving off gives an immediate indication that the system is working. Steering will feel light when power steering is working, but heavy if not working.
2) Open the bonnet, identify where you would check the engine oil level and tell me how you would check that the engine has sufficient oil.
CLICK FOR ANSWER
Open the bonnet, identify dipstick/oil level indicator. Describe how to check level against min/max marks. CHECK LEVELS WHEN ENGINE IS COLD.
3) Open the bonnet, identify where you would check the engine coolant level and tell me how you would check that the engine has the correct level.
CLICK FOR ANSWER
Open the bonnet, identify engine coolant cap and check level of green fluid (antifreeze and water) is between maximum and minimum level markers. ENGINE MUST BE COLD as when HOT fluid is under pressure and could burn.
4) Identify where the windscreen washer reservoir is and tell me how you would check the windscreen washer level.
CLICK FOR ANSWER
Identify reservoir and explain how to check level.
5) Open the bonnet and show me how to check the brake fluid level.
CLICK FOR ANSWER
Open the bonnet, identify the brake fluid reservoir, the level against min markings on the side. If not visible unscrew cap and check level.
6)
Show me how you would check the parking brake for excessive wear.
CLICK FOR ANSWER
Operate handbrake with foot on footbrake. Handbrake secures itself and does not reach the end of its travel.
7) Show me how you would check the horn is working (OFF ROAD ONLY).
CLICK FOR ANSWER
Press it.
8) Show me how you would check the direction indicators are working.
CLICK FOR ANSWER
Operate indicators or hazard warning lights and get out and check them.
9) Tell me how you would check the headlights/taillights are working.
CLICK FOR ANSWER
Switch lights on, walk round vehicle.(As this is a ‘’Tell Me’’ question there is no need to physically check the lights).
10) Show me how you switch your headlights from dipped to main beam and explain how you would know the main beam is on whilst inside the car.
CLICK FOR ANSWER
Operate switch (with ignition or engine on if necessary). Check the main beam warning light.
11) Show me how you would switch on the rear fog light(s) and explain when you would use it/them.
CLICK FOR ANSWER
Operate switch (turn on dipped headlights and ignition if necessary). Check warning light is on. Use it/them when visibility is 100m or less.
12) Tell me how you would check the brake lights are working.
CLICK FOR ANSWER
Operate brake pedal, make use of reflections in windows, garage doors, etc, or ask someone to help.
13) Tell me how you would know if there was a problem with your anti-lock braking system.
CLICK FOR ANSWER
Warning light should illuminate if there is a fault with your anti-lock braking system (ABS).
14) Tell me how you would check that the brakes are working before starting your journey.
CLICK FOR ANSWER
Brakes should be tested as you set off slowly. Vehicle should not pull to one side. Brakes should not feel spongy or slack.
15) Tell me where you would find the information for the recommended tyre pressures and how they should be checked.
CLICK FOR ANSWER
Look in the manufacturers guide and use a reliable pressure gauge. Adjust pressure when tyres are cold, do the spare as well, refit valve caps.
16) Tell me how you would check the tyres to ensure they have sufficient tread depth and that their general condition is safe to use on the road.
CLICK FOR ANSWER
1.6mm of tread depth across the central three quarters of the breadth of the tyre and around the entire outer circumference. No cuts or bulges.
17) Show me how you would set the demister controls to clear all the windows effectively, this should include both front and rear screens.
CLICK FOR ANSWER
Set relevant controls including; fan, temperature, air direction/source and heated screen to clear windscreen and windows. Engine does not have to be started for this demonstration.
18) Tell me how you make sure your head restraint is correctly adjusted so it provides the best protection in the event of a crash.
CLICK FOR ANSWER
The head restraint should be adjusted so the rigid part of the head restraint is at least as high as the eye or the top of the ears and as close to the back of the head as is comfortable. NB. Some restraints might not be adjustable.
19) Show me how you would clean the windscreen using the windscreen washer and wipers.
CLICK FOR ANSWER
Operate control to wash and wipe windscreen.(Turn on ignition if necessary). |
